High quality electronic components info database? Easybom, an international integrated service provider for the electronics industry, persists in pursuing the concept of “win-win”. Dedicated to providing electronic component big data information services that are maintained by senior industry engineers, easybom has established an excellent communication platform for merchandisers, suppliers, and engineers through our powerful electronic component search engine. Easybom will keep focusing on the leverage of our high-quality services for data mining and information matching. Easybom provides intelligent data analysis to enhance your insight into the market. It focuses on the market as well as your need. Easybom establishes a communication bridge for suppliers, purchasers and engineers with electronic component data as its core. Read extra details on find electronic parts.

In the past Wi-Fi technology, intercell co-channel interference (Co-Channel Interference,CCI) is another important factor affecting channel capacity. The core of CSMA/CA is to listen before you speak (listen before talk,LBT). The device monitors the wireless channel first and sends data without being occupied. In the case of multi-AP mesh networking (AP,Access Point, wireless access point), the equipment in the cell will listen to the interference signal of the cell adjacent to the same channel, causing the device to mistakenly think that the wireless channel of the cell is being occupied at this time, so stop transmitting. This kind of interference will significantly reduce the network capacity when the network is not optimized or the number of available channels is very small. As shown in the figure below, the four Wi-Fi AP are networked with three channels. However, since there are only three channels available, AP1 and AP2 have to be deployed on the same channel Channel 6, when the signal of AP2 is interference to the user equipment belonging to AP1-Overlapped Basic Service Set (OBSS, overlapping basic service units, which can be understood as overlapping cells with the same frequency).

Due to the spread of the global COVID-19 epidemic in 2020, automobile production is in the doldrums (figure 1). The number of cars produced worldwide, which was 92.18 million in 2019 before the COVID-19 epidemic, fell by 14.56 million to 77.62 million in 2020 and appears to have fallen by 1.2 million to 76.42 million in 2021. The decline in car production in 0A2020 was caused by the COVID-19 epidemic, which led to a sharp drop in demand. However, the downturn in car production in 2021 is mainly due to a shortage of semiconductors. In fact, by 2021, the shortage of semiconductors has made it impossible to build cars, and the governments of Japan, the United States and Germany, with automobile as the core industry, have made requests to TSMC to increase the production of on-board semiconductors through the government of Taiwan. The semiconductors in short supply at that time were 28nm logic semiconductors and MCU (Micro Controller Units, commonly known as “microcontrollers”).

In the early CPUs, the chip integration level was very low. The CPU was a single chip. It only integrated an arithmetic unit and a controller. It could only calculate and control. At this time, the internal capacity of the CPU was useless. Memory, the CPU left The memory cannot be calculated. Back then, there was no memory in the CPU because the memory could not be integrated, and others such as the serial port could not be integrated, so there was only a single CPU. If you need to use the serial port, you need to use a serial port controller chip outside the CPU. The PCB traces are connected to the CPU, and then the entire PCB board is composed of the CPU, and these peripheral chips is called a system board. This system board can communicate with another system board. The CPU communicates with another system through its serial port controller. The serial port controller on the board communicates, and functions such as the serial port controller cannot be integrated into the CPU chip. For example, if the LCD is also used here, it is necessary to add an LCD controller chip to the periphery and connect it to the CPU through wiring. A whole board composed of these chips is called a system board. These UART controllers and LCD controllers are called peripherals. Combining them with the CPU on one board is the function implemented by a current K60 chip, but they are integrated into a small chip. The peripherals here refer to the inside of the system board, the peripherals outside the CPU are called peripherals, the CPU is called the internals, and there are only arithmetic units and controllers inside, which are called internals.

Excellent BOM Tool: Customer’s bill of materials verification; Real-time Quote Response; Customer’s bill of materials verification; Intelligently link the customer’s data in the BOM, accurate industry part numbers, and rich parts industry information, so as to improve the efficiency of BOM cleaning. PDF Download: Download the PDF file from the product detail page to quickly understand all basic information and manufacturer information. CAD Download: Download the CAD model from easybom. See more info at https://www.easybom.com/.